Gao, Fracture Resistance of High Entropy Alloys: A Review, Intermetallics, 2018, 99, p 69–83. Ritchie, Exceptional Damage-Tolerance of a Medium-Entropy Alloy CrCoNi at Cryogenic Temperatures, Nat. George, Tensile Properties of High- and Medium-Entropy Alloys, Intermetallics, 2013, 39, p 74–78.ī. Šmilauerová, Structure and Mechanical Properties of FeAlCrV and FeAlCrMo Medium-Entropy Alloys, Mater. George, Reasons for the Superior Mechanical Properties of Medium-Entropy CrCoNi Compared to High-Entropy CrMnFeCoNi, Acta Mater., 2017, 128, p 292–303. Wu, Dynamic Shear Deformation of a CrCoNi Medium-Entropy Alloy with Heterogeneous Grain Structures, Acta Mater., 2018, 148, p 407–418. Yeh, Physical Metallurgy of Concentrated Solid Solutions from Low-Entropy to High-Entropy Alloys, Curr. Yeh, Alloy Design Strategies and Future Trends in High-Entropy Alloys, JOM, 2013, 65(12), p 1759–1771.Ĭ.Y. Tasan, Metastable High-Entropy Dual-Phase Alloys Overcome the Strength-Ductility Trade-Off, Nature, 2016, 534(7606), p 227–230. Yeh, High-Entropy Alloys: A Critical Review, Mater. Liaw, Deviation from High-Entropy Configurations in the Atomic Distributions of a Multi-principal-Element Alloy, Nat. Yang, High-Entropy Alloy: Challenges and Prospects, Mater. Raabe, A Novel, Single Phase, Non-equiatomic FeMnNiCoCr High-Entropy Alloy with Exceptional Phase Stability and Tensile Ductility, Scripta Mater., 2014, 72, p 5–8. Lu, Microstructures and Properties of High-Entropy Alloys, Prog. Raabe, Atomic-Scale Compositional Characterization of a Nanocrystalline AlCrCuFeNiZn High-Entropy Alloy Using Atom Probe Tomography, Acta Mater., 2013, 61(12), p 4696–4706. Ranganathan, High-Entropy Alloys, Butterworth-Heinemann, Oxford, 2014. Chang, Nanostructured High-Entropy Alloys with Multiple Principal Elements: Novel Alloy Design Concepts and Outcomes, Adv. Vincent, Microstructural Development in Equiatomic Multicomponent Alloys, Mater. Cantor, Multicomponent and High Entropy Alloys, Entropy, 2014, 16, p 4749–4768.ī. Qian, Light Alloys: Metallurgy of the Light Metals, Elsevier Science, Amsterdam, 2017.ī. This counterbalancing effect from mixing enthalpy led to a simple microstructure, thereby enhancing the mechanical properties in the currently developed Mg MEA. However, multiple phase formation was mitigated due to the suitable mixing enthalpy (Δ H mix: − 4.52 kJ/mol). From the alloy design perspective, a large atomic size difference ( δ: 8.49%) in the alloy was the main cause for the intermetallic formation. Unlike reported MEAs, currently developed Mg MEA revealed a relatively simple microstructure with three major phases. The current lightweight Mg MEA reached a plasticity of more than twice of cast alloy and more than five times in the case of extruded alloy when compared to reported MEAs’ plasticity in open literature. Previously reported lightweight MEAs exhibited a limited plasticity up to 6.5% in the cast form. Compressive strength and plasticity increased from 444 MPa and 13.9% in cast alloy to 675 MPa and 32.7% in extruded alloy. In line with the change in microstructure, remarkably improved compressive properties were realized in extruded alloy as compared to cast alloy. A change in intermetallics morphology from continuous pattern in cast alloy to discontinuous pattern in extruded alloy was observed. Secondary processing such as extrusion was applicable on the cast alloy due to its high deformability. Currently developed Mg MEA showed an appreciable plasticity of 13.9% in as-cast condition. The reported medium entropy alloys based on light metals, such as aluminum and magnesium, exhibit very low plasticity, and only cast alloys’ properties were investigated. The multicomponent alloy with a composition, Mg 62Li 13Zn 12Cu 10Y 3 (at.%), was processed using disintegrated melt deposition technique. The present study focused on the development of magnesium-based medium entropy alloy (Mg MEA).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |